长江科学院院报 ›› 2016, Vol. 33 ›› Issue (3): 127-131.DOI: 10.11988/ckyyb.20140826

• 水工结构与材料 • 上一篇    下一篇

水工钢闸门主梁的最优梁高

张雪才, 王正中, 孟明, 李路明   

  1. 西北农林科技大学 水利与建筑工程学院, 陕西 杨凌 712100
  • 收稿日期:2014-09-15 出版日期:2016-03-01 发布日期:2016-03-09
  • 通讯作者: 王正中(1963-),男,陕西彬县人,教授,博士生导师, 主要从事水工程安全及其灾害防治理论与技术研究,(电话)13319210121(电子信箱)wangzz0910@163. com。
  • 作者简介:张雪才(1990-),男,河南项城人,硕士研究生,主要从事水工结构稳定及优化研究,(电话)15202495509(电子信箱)xnzxc1990@163.com。
  • 基金资助:
    国家自然科学基金项目(51179164)

Optimal Height of Main Beam of Hydraulic Steel Gate

ZHANG Xue-cai , WANG Zheng-zhong , MENG Ming , LI Lu-ming   

  1. College of Water Resources and Architecture Engineering, Northwest A &F University, Yangling 712100, China
  • Received:2014-09-15 Online:2016-03-01 Published:2016-03-09

摘要: 对水工钢闸门主梁高度的确定多以经验公式为主,理论不完善,未全面考虑截面形式与支座位置对梁高影响的问题,依据现行钢闸门设计规范,以满足强度、刚度、稳定性和几何构造要求为约束条件,以主梁和竖向隔板总用钢量最小为目标函数,分别建立单轴、双轴对称截面下的简支式和双悬臂式主梁梁高的优化模型。采用半解析法推导出简支式和双悬臂式主梁的最优梁高理论公式。通过与已建工程对比,结果表明:推导的最优梁高公式计算的梁高均与实际工程中的梁高接近,且公式有进一步优化的空间;通过减小隔板高厚比与主梁腹板高厚比可达到降低梁高的目的。该理论公式一方面可应用于工程实践,另一方面也可为完善规范提供理论基础。

关键词: 水工结构, 钢闸门主梁, 工字形截面最优梁高, 优化模型, 理论公式

Abstract: At present, there are several problems in determining the height of main beam in hydraulic steel gate, including a large number of empirical formulas, imperfect theories, and ignorance of influences of section form and support position. According to design code of steel gate, with requirements of strength, stiffness, stability and geometric structure as constraint conditions, we take minimum steel amount of main beams and vertical baffles as objective function, and establish optimization models for beam height of simple support and double cantilever’s girder under conditions of uniaxial and biaxial symmetrical sections. Theoretical formulas of optimal girder height are derived by semi-analytical methods. Through comparing with built projects, we find that girder heights calculated by the theoretical formulas in this paper are close to those in practical projects, which still can be optimized. Furthermore, we can decrease beam height through reducing height-thickness ratios of partition and web of main beam. The theoretical formulas can be applied to engineering practice, and also provide a theoretical basis for improving specification.

Key words: hydraulic structure, main beam of steel gate, optimal height of H-shaped beam, optimization model, theoretical formula

中图分类号: