PDF(1501 KB)
Quasi-static Analysis of Anchoring Mechanism of Pressure-dispersed Anchor Cables under Seismic Action
YE Hong, TAO Ting-quan, CHEN Yan-ping, LI Yan, FAN Wei-qin, LEI Li-zhi, CHEN Chen
Journal of Changjiang River Scientific Research Institute ›› 2026, Vol. 43 ›› Issue (11) : 111-119.
PDF(1501 KB)
PDF(1501 KB)
Quasi-static Analysis of Anchoring Mechanism of Pressure-dispersed Anchor Cables under Seismic Action
[Objective] Due to the structural complexity of pressure-dispersive anchor cables and the concealed nature of the anchorage section, existing theories on their anchoring mechanism are difficult to apply to complex engineering practices. In particular, theoretical research on their behavior under seismic loading remains insufficient. This study aims to further investigate the anchoring mechanism and seismic performance of pressure-dispersive anchor cables. Using the Mindlin solution as the theoretical core and combining it with the equivalent quasi-static method, a theoretical analysis of the anchoring mechanism under seismic action was conducted. [Method] Based on the equivalent quasi-static method and the Mindlin solution, expressions for the compressive stress of the grout and the side friction resistance between the rock-soil mass and the anchorage body in the anchorage section were derived. Through a case study, the stress distribution characteristics of multi-anchorage units and the influence of key parameters under the coupled action of prestress and seismic loads were systematically analyzed. [Results] (1) Pressure-dispersive anchor cables achieve redistribution of grout compressive stress and anchorage side friction through hierarchical load transfer across multiple anchorage units. This avoids the accumulation of local plastic damage in the grout caused by stress concentration, thereby enhancing the seismic performance of the anchoring system. (2) A negative correlation exists between the size of the anchor hole (or bearing body) and the peak values of grout compressive stress and anchorage side friction. Increasing the anchor hole (or bearing body) size effectively improves the uniformity of load transfer, inhibits local bond-slip failure, buffers the impact of seismic loads to some extent, and enhances the energy dissipation capacity of the anchoring system. (3) The dynamic response to the Poisson’s ratio of the rock mass shows an opposite trend: the peak grout compressive stress increases while the peak anchorage side friction decreases. This reflects the coupled mechanism of confining pressure constraint and interfacial shear stress transfer efficiency, which jointly influence the dynamic response characteristics of the anchorage section during earthquakes. (4) Both seismic and prestress loads are linearly positively correlated with the peak grout compressive stress and peak anchorage side friction. Increasing either the prestress or seismic load raises these peak values, thereby exacerbating the risk of dynamic damage to the anchorage section. [Conclusions] This study reveals the stress redistribution mechanism of pressure-dispersive anchor cables, providing a theoretical basis and design reference for the seismic design of slope anchoring engineering.
geotechnical engineering / pressure-dispersive anchor cable / Mindlin’s fundamental solution / quaisi-static method / seismic mechanism
| [1] |
王勇华, 王小勇, 牛云彪, 等. 黄土地区压力型锚索锚固机理数值模拟研究[J]. 地下空间与工程学报, 2020, 16(增刊2):693-701.
(
|
| [2] |
雷金山, 杨秀竹, 王安正, 等. 压力型锚索原型试验及应力分布规律研究[J]. 铁道科学与工程学报, 2012, 9(1): 90-94.
(
|
| [3] |
王开彬, 刘钦, 王洪涛. 压力型锚索锚固段荷载传递特征及影响因素研究[J]. 黄金科学技术, 2024, 32(1): 123-131.
为了研究土层压力型锚索锚固段的荷载传递特征及滑脱过程,在理论分析的基础上推导出压力型锚索在外荷载作用下的剪应力和轴力分布规律公式,详细分析了各影响因素对轴向力和剪应力的影响程度。研究结果表明:锚索锚固段的剪应力和轴力分布函数均为幂函数;剪应力和轴力大小及分布范围取决于锚固力,并与锚固体直径、锚固体弹性模量和泊松比、土的压缩模量和泊松比以及锚固体和土间界面的摩擦角有关;预应力锚索锚固段的最大剪应力位置仅与锚固体直径、土体性质、锚固体材料参数和半径有关;锚固体直径的大小对剪应力和轴力均有显著影响;在不同荷载作用下,锚固体界面剪应力的分布形式、范围和峰值位置均相同。现场原位试验结果表明:理论分析结果与工程实践结果吻合性较好。研究结果可为分析土体锚固工程的受力状态及优化设计提供依据。
(
In order to study the load transfer characteristics and the slippage process of anchorage segment of the pressure-type anchor cable in soil strata,the formula of shear stress and axial force distribution of the anchor cable under external load was derived based on theoretical analysis.In addition,the load transfer characteristics was analyzed.The influence degree of soil compressive modulus,anchor diameter,load and Poisson’s ratio on axial force and shear stress were analyzed in detail.The shear stress and axial force in the anchorage segment of the cable has the same distribution function and is all power functions.The shear stress and axial force are the largest near the bearing plate,but far from the bearing plate,the shear stress and axial force gradually decrease to zero.The magnitude and distribution range of the shear stress and axial force in the anchorage segment mainly depend on the anchorage force,and are related to the diameter,elastic modulus and Poisson ratio of anchor body,the compressibility modulus and Poisson ratio of soils,and friction angle of the interface between anchors and soils.In the form of the formula,if the anchorage segment is infinite,the anchoring force P can be infinite in theory.The ultimate anchoring force depends on the strength of the anchors around the bearing plate,the soil and the interface.The position of the maximum shear stress is only related to the soil properties,material parameters and radius of anchorage in anchorage segment of prestressed cable,not related to the magnitude of load.The diameter of anchors also has significant influence on the distribution of shear stress and axial force.With different loads,the distribution form,range and peak position of shear stress is the same,which is independent of load.Under the same conditions,the larger the compressive modulus of soil,the larger of shear stress,and the faster the shear stress decline trendation.The Poisson’s ratio has little effect on the shear stress.When the value of Poisson’s ratio is different,the mechanical property of the whole anchorage system under external load is basically unchanged,and also the value of shear stress.The range of action remains and the axial force is unchanged.In order to verify the correctness of the theoretical analysis results,the load transfer test results of the anchor cable were obtained by in-situ tests of clay and sandy soil.The in-situ test results show that the theoretical analysis results are in good agreement with the engineering results.The research results can provide a basis for analyzing the stress state and optimizing design of soil anchorage engineering. |
| [4] |
GB 50086—2015 岩土锚杆与喷射混凝土支护工程技术规范[S].(GB 50086—2015 Technical code for engineering of ground anchorages and shotcrete support[S].) (in Chinese)
|
| [5] |
周平. 高边坡压力分散型锚索预应力施工技术[J]. 工程与建设, 2024, 38(5):1162-1164,1168.
(
|
| [6] |
王勇华, 熊二刚, 王小勇. 黄土中压力型锚索锚固段应力分析[J]. 力学季刊, 2020, 41(2): 231-239.
为研究黄土地区压力型锚索锚固机理,根据压力型锚索锚固段受力状态,基于三线型剪切-滑移模型,推导了注浆体与岩土体界面在弹性阶段所对应的剪应力及轴向应力分布的闭合解.根据相关压力型锚索锚固试验数据,采用推导的闭合解计算了不同张拉荷载作用下界面的剪应力分布,并与试验结果进行了对比.结果表明,各级张拉荷载作用下注浆体/岩土体界面剪应力的分布及其最大值与试验结果基本吻合,验证了本文提出解析模型的正确性与可靠性;压力型锚索锚固界面剪应力呈指数分布规律,在承压板附近剪应力分布集中且应力较大,随着离承压板距离的增大,剪应力逐渐减小;压力型锚索锚固界面剪应力峰值随外荷载增大而增大.研究结果可为压力型锚索的设计和计算提供一种理论参考.
(
In order to study the anchoring mechanism of the compression anchors in the loess area, the closed-form solutions for the interfacial shear stress distribution and axial stress distribution along the bond length were derived using the tri-linear model of bond-slip relationship. The related experimental data of the compression anchors were compared to validate the analytical model. The interfacial shear stress distribution by the derived solution is in a good agreement with the experimental results, which demonstrates the validity and reliability of the proposed analytical model. The results indicate that the interfacial stress distribution exhibits an exponential distribution, the interfacial stress is very high near the bearing plate, and reduces with increasing the distance from the bearing plate; the peak shear stress increases with the tensile loads. The research results herein can provide a theoretical basis for the design and calculation of this kind of compression anchors.
|
| [7] |
叶红, 陶廷权, 李艳. 地震作用下压力型锚索锚固段受力状态理论分析[J]. 长江科学院院报, 2023, 40(4):107-112,118.
为更加精确地研究地震作用下压力型锚索的锚固机理,根据Mindlin基本解,结合单自由度体系的有阻尼强迫振动特点,推导了压力型锚索锚固段注浆体受到的压应力表达式和锚固段较软岩体与注浆体之间剪应力表达式。通过算例分析了简谐荷载的幅值、简谐荷载的圆频率以及低阻尼体系的阻尼比等因素对压力型锚索加固效果的影响。研究结果表明:简谐荷载的幅值和圆频率对压力型锚索加固效果影响较大,低阻尼体系的阻尼比对压力型锚索加固效果影响较小;简谐荷载的幅值与注浆体受到的应力呈线性关系;简谐荷载的圆频率与压力型锚索体系的有阻尼自振圆频率越接近,注浆体受到的应力越大。研究成果可为压力型锚索加固岩土体的抗震设计提供一定的理论参考。
(
|
| [8] |
屈文涛, 马丽娜, 田晓, 等. 压力分散型锚索锚固段应力分布及影响参数分析[J]. 水利与建筑工程学报, 2021, 19(5): 23-27.
(
|
| [9] |
张春文, 张艳, 徐民, 等. 公路高边坡压力分散型锚索锚固段应力分布规律理论研究[J]. 价值工程, 2022, 41(23): 114-116.
(
|
| [10] |
芮瑞, 夏元友, 顾金才, 等. 压力分散型锚索非均匀剪应力设计方法[J]. 岩土工程学报, 2012, 34(7): 1262-1270.
(
|
| [11] |
姚海波, 干昆蓉, 伍冬, 等. 压力分散型锚索与拉力集中型锚索抗振性能研究[J]. 岩土力学, 2012, 33(12):3598-3603.
(
|
| [12] |
赖杰, 郑颖人, 方玉树, 等. 预应力锚索支护边坡地震作用下动力响应研究[J]. 地下空间与工程学报, 2011, 7(增刊2):1768-1773.
(
|
| [13] |
叶红, 陶廷权, 李艳, 等. 考虑倾角影响压力型锚索锚固段应力的近似理论分析[J]. 长江科学院院报, 2025, 42(1): 136-143.
为了更加精确地研究压力型锚索的锚固机理,考虑平面应力状态的应力分析,基于明德林(Mindlin)理论解推导了压力型锚索锚固段注浆体所受压应力的近似理论解和锚固体与岩土层间剪应力的近似理论解,并进行了算例分析。研究结果表明:锚索倾角与压力型锚索锚固段注浆体应力分布曲线之间存在负相关关系,锚索倾角与锚固段注浆体应力峰值之间存在幂函数关系,且锚索倾角对锚固段注浆体所受压应力和锚固体与岩土层间剪应力的影响较大。所得研究结果进一步丰富了压力型锚索锚固技术的理论研究内容,可为新型锚固技术的开发应用提供一定的参考,也为压力型锚索加固岩土体设计提供理论支撑。
(
|
| [14] |
叶红, 陶廷权. 地震作用下压力型锚索锚固段设计分析[J]. 武汉理工大学学报, 2023, 45(1): 80-84.
(
|
| [15] |
叶红, 陈燕平. 风化砂岩中压力型锚索锚固机理的拟静力分析[J]. 中国科技论文, 2019, 14(6): 589-594, 641.
(
|
| [16] |
叶红, 陈燕平. 基于Mindlin解地震作用下压力型锚索的拟静力分析[J]. 振动与冲击, 2017, 36(2):221-228.
(
|
| [17] |
叶红. 锚索孔周边岩体弹性模量的数值模拟分析[J]. 武汉交通职业学院学报, 2012, 14(2): 72-74.
(
|
| [18] |
邱滟佳, 张鸿儒, 于仲洋. 考虑土与结构相互作用的建筑地下室抗震设计方法[J]. 东南大学学报(自然科学版), 2021, 51(2): 285-293.
(
|
| [19] |
周德培, 张建经, 汤涌. 汶川地震中道路边坡工程震害分析[J]. 岩石力学与工程学报, 2010, 29(3): 565-576.
(
|
| [20] |
GB 50330—2013 建筑边坡工程技术规范[S].(GB 50330—2013 Technical code for building slope engineering[S].) (in Chinese)
|
| [21] |
GB 50011—2010(2016年版) 建筑抗震设计规范[S].(GB 50011—2010(2016edition) Code for seismic design of buildings[S]. ) (in Chinese)
|
| [22] |
叶红, 陈燕平. 耦合效应下压力型锚索锚固机理的拟静力分析[J]. 长江科学院院报, 2020, 37(8): 89-94.
(
In the purpose of studying the seismic behavior of pressure-type cable in weak rock and soil under earthquake more accurately, the expressions of prestress and prestress loss under the coupling effect of prestress of anchor rope and creep of rock and soil mass were derived based on the material relaxation of steel strand subjected to long-term load. Furthermore, the expressions of equivalent compressive stress and equivalent shear stress of the anchorage segment of pressure-type anchor cable under circular uniform load were derived using pseudo-static method, Mindlin basic solution and integral simplification method. Case study demonstrated that the loss of prestress was large in the initial stage, stabilized in mid-stage and changed little in later stage, with the loss rate declining consistently. The equivalent stress of mortars in anchorage segment concentrated mainly within 0.5 m from the pressure plate. The maximum equivalent stress was in 0.1 m from the pressure plate rather than on the contact surface between pressure plate and mortars. The research findings enriched the theoretical research in regards to seismic design of pressure-type anchor cables, and offered some references for the reasonable seismic design of slope strengthened with pressure-type cable.
|
| [23] |
|
| [24] |
王士杰, 张梅, 张吉占. 对Mindlin解求地基附加应力的进一步探讨[J]. 四川建筑科学研究, 2000, 26(1): 51-54.
(
|
| [25] |
叶红, 陈燕平. 耦合效应下压力型锚索锚固机理的近似理论分析[J]. 人民长江, 2020, 51(5): 178-183.
(
|
| [26] |
|
| [27] |
T/CECS 22—2024 岩土锚杆技术规程[S].(T/CECS 22—2024 Technical standard for ground anchor[S].) (in Chinese)
|
| [28] |
夏元友, 陈泽松, 顾金才, 等. 压力分散型锚索受力特点的室内足尺模型试验[J]. 武汉理工大学学报, 2010, 32(3): 33-37.
(
|
| [29] |
芮瑞, 夏元友, 顾金才, 等. 压力分散型锚索锚固段受力特性试验分析[J]. 岩土工程学报, 2012, 34(5):917-923.
(
|
/
| 〈 |
|
〉 |